Welcome to RH Electronics

HV PMT

The category of High Voltage Power Supply Modules for Geiger tubes and Photomultiplier tubes.

10 Item(s)

per page

Set Descending Direction
  1. Plastic Socket for Photomultiplier PMT Tube 14pin compatible to Hamamatsu E678-14C for R268 R6094 R6095
  2. Socket for Photomultiplier PMT Tube 14pin compatible to Hamamatsu E678-14C for R268 R6094 R6095
  3. Gamma Scintillator Driver Wired Socket for R6094 R6095 PMT

    Gamma Scintillator Driver Module wired with Socket for R6094 R6095 PMT

    $175.00

    Gamma Scintillator Driver Module wired with Socket for R6094 R6095

    14 pin Hamamatsu socket wired to divider board with pulse processing circuit and High Voltage board to power the PMT tube. Intended for scintillation detector build with R6094/R6095 tube. The module require only 5V to work and has ready digitized PMT pulses on the output.

    Technical specifications:

    • Directly compatible and plugable to Hamamatsu R6094 / R6095 PMT tube
    • Adjustable stabilized and filtered High Voltage for PMT, negative polarity -500V to -1000V
    • Adjustable pulse threshold level
    • Original PMT socket intalled and wired
    • Includes high impedance voltage divider for dynodes
    • Require only 5V to work
    • Low power comsumptions to fit portable scintillation counters
    • Digitized PMT pulses output compatible with Arduino / PIC / AVR /MSP430
    • Compatible with DIY Scintillation Counters
    • Shipping Weight: 250gr
    • UPC Number: 634154871164
    • SKU: RH-K-PMT-3
    Learn More
  4. Gamma Spectrometry DIY HV Negative Polarity Power Supply

    NEGATIVE Polarity 1KV HV High Voltage PMT Power Supply -700V - 1000V for Photomultiplier Tube

    $85.00

    NEGATIVE Polarity 1KV High Voltage for PMT and Gamma Spectroscopy

    Low ripple Adjustable Power Supply Unit Negative polarity -700v-1000v with Metal Enclosure. The power supply has excellent HV regulation and additional filtration for the clean DC output. Reverse polarity protection included. The board has low quiescent current of 6mA non-loaded and 10mA with 100M load. Maximum output current on -1000V is 100uA, but it's recommended to use this power supply only with high impedance PMT divider of 100 Mega ohm.

    You can trim HV output with miniature potentiometer inside the unit enclosure. Default preset is for minus -850V that usually fit many Photomultiplier tubes. Measure HV with 10M multimeter on the daburn wire output.

    This power supply can be used for DIY Spectroscopy projects or driving Scintillation Probes. The module comes installed into metal enclosure for full shielding to protect your project from DC-DC conversion noise.

    Technical Specifications:

    • Negative Polarity High Voltage stabilized output: -700V-1000V
    • Compatible with DIY Scintillation Probes
    • Input DC voltage: 4.8V-5.5V stabilized
    • Input DC voltage with supplied 2.1 custom connector: 6.5V - 14.50V not stabilized
    • Input current consumption with 100M load at -1000V: 10mA
    • Quiescent current at -1000V: 6mA
    • Full start time: app. 15 seconds with 100M probe load
    • Recommended load of the PMT probe divider: 80-100 Mega ohm
    • Reverse polarity protection included
    • Excellent DC output filtartion
    • Metal Enclosure for full noise shielding
    • Comes with branded Daburn high voltage wire
    • Comes with custom made 2.1 DC connector-wire with installed low drop 5V regulator
    • HV Power Supply dimensions: 115x60x30 mm
    • Shipping Weight: 500gr
    • UPC Number: 635292807411
    • SKU: RH-K-PMT-2-NG
    Learn More
  5. Gamma Spectrometry DIY HV Power Supply

    POSITIVE Polarity 1KV HV High Voltage PMT Power Supply 700V - 1000V for Photomultiplier Tube

    $85.00

    POSITIVE Polarity 1KV High Voltage for PMT and Gamma Spectroscopy

    Low ripple Adjustable Power Supply Unit Positive polarity 700v-1000v with Metal Enclosure. The power supply has excellent HV regulation and additional filtration for the clean DC output. Has reverse polarity protection with original supplied DC connector. The board has low quiescent current of 3mA non-loaded and 6mA with 100M load. Maximum output current on 1000V is 100uA, but it's recommended to use this power supply only with high impedance PMT divider of 100 Mega ohm.

    You can trim HV output with miniature potentiometer inside the unit enclosure. Default preset is for 900V that usually fit many Photomultiplier tubes. Measure HV with 10M multimeter on the daburn wire output.

    This power supply can be used for DIY Spectroscopy projects or driving Scintillation Probes. The module comes installed into metal enclosure for full shielding to protect your project from DC-DC step-up noise.

    Technical Specifications:

    • Positive Polarity High Voltage stabilized output: 700V-1000V
    • Compatible with DIY Scintillation Probes
    • Battery DC voltage: 4.8V-5.5V
    • Battery current with 100M load at 1000V: 6mA
    • Battery quiescent current at 1000V: 3mA
    • Full start time: app. 15 seconds with 100M probe load
    • Recommended load of the PMT probe divider: 80-100 Mega ohm
    • Reverse polarity protection included
    • Excellent DC output filtartion
    • Metal Enclosure for full noise shielding
    • Comes with branded Daburn high voltage wire
    • HV Power Supply dimensions: 115x60x30 mm
    • Shipping Weight: 500gr
    • UPC Number: 635292807411
    • SKU: RH-K-PMT-2-PS
    Learn More
  6. Gamma Spectrometry DIY Kit Driver with HV Power Supply and Pre-Amplifier

    Gamma Spectrometry Detector Driver DIY Kit High Voltage Power Supply 700V-1000V with Spectroscopy PMT Amplifier

    Regular Price: $125.00

    Special Price $99.95

    Gamma Spectrometry Driver DIY Kit - Available for Order.

    Gamma Spectroscopy Driver DIY Kit include low ripple Adjustable Power Supply Unit 700v-1000v with Metal Enclosure and Charge-Sensitive mini amplifier module. Now the kit comes with new updated amplifier module! This kit can be used as Spectrometry Driver for your own DIY PMT probe. The amplifier output is compatible with freeware PRA Pulse Height Analysis software.

    Power supply unit and pre-amplifier are sold fully soldered. HV unit installed into separated metal enclosure. Please refer recommended installation diagram for the final project.

    Technical Specifications:

    • Positive / Negative Polarity High Voltage stabilized output: 700V-1000V
    • Compatible with DIY Scintillation Probes
    • Compatible with freeware PRA Software
    • Input DC voltage: 4.8V-5.5V stabilized
    • Input current with 100M load at 1000V: 6mA - 10mA
    • Quiescent current at 1000V: 3mA - 6mA
    • Pulse length: adjustable 50uS-250uS
    • Full start time: app. 15 seconds with 100M probe load
    • Recommended load of the PMT probe divider: 80-100 Mega ohm
    • HV Power Supply dimensions: 115x60x30 mm
    • Pre-AMP PCB dimensions: 29x24 mm
    • Shipping Weight: 500gr
    • UPC Number: 635292807404
    • SKU: RH-K-PMT-2
    Learn More
  7. PMT Photomultiplier Charge Sensitive Amplifier Module for DIY Gamma Spectrometry

    PMT Photomultiplier Charge Sensitive Amplifier Module for DIY Gamma Spectrometry

    $25.00

    Updated Charge Sensitive Amplifier for Gamma Spectrometry

    Amplifier module for DIY Gamma Spectrometry Project. The charge sensitive amplifier can be used with Positive or Negative polarity photomultiplier setup. The module originally comes with our DIY Gamma Spectrometry kit, but now can be purchased separately if you want to upgrade your old AMP or just need PMT pulse amplifier for your project.

    Technical Specifications:

    • Positive / Negative PMT configuration available, Positive by default
    • Compatible with DIY Scintillation Probes
    • Compatible with freeware PRA Beqmoni Software
    • Supply DC voltage: 4.5V-12V
    • Pulse length: adjustable 50uS-250uS
    • SMA jack for signal output
    • Pre-AMP PCB dimensions: 29x24 mm
    • Shipping Weight: 100gr
    • SKU: RH-K-PMT-AMP
    Learn More
  8. PMT Photomultiplier Tube High Voltage Power Supply DIY Kit 700V - 1000V

    PMT Photomultiplier Tube / Geiger Tube High Voltage Power Supply DIY Kit 700V - 1000V

    $49.95

    Adjustable Power Supply Module 700V - 1000V for PMT Photomultiplier Tube or Geiger Tube.

    DIY soldering kit for Positive HV High Voltage Power Supply 700V-1000V, positive output. Compatible with  DIY PMT / Photomultiplier Scintillation probes / can be used for rare high voltage Geiger tubes. This kit is recommended only for experienced hobbyist who know how to use high voltage devices safely.

    Technical Specifications:

    • Positive High Voltage stabilized adjustable output: 700V-1000V
    • Compatible with DIY Scintillation Detectors
    • Compatible with rare Geiger Tubes
    • Battery DC voltage: 4.8V-5.5V
    • PCB dimensions: 140mm x 45mm
    • Shipping Weight: 200gr
    • UPC Number: 635292807398
    • SKU: RH-K-PMT-1


    Learn More
  9. High Voltage Geiger Probe Driver Power Supply Module 380V-550V with TTL Output

    High Voltage Geiger Probe Driver Power Supply Module 380V-550V with TTL Digitized Pulse Output

    $45.00

    Adjustable High Voltage Power Supply Module with TTL output.

    With a standard construction of wired GM probe, where high voltage transferred over a cable, you get the HV performance drop and tube signal attenuation when counting rate is increasing over 30000 CPM. Despite the standard GM probe construction, the "RH High Voltage Probe Driver" uses different method of signal path and allows you to drive very long probe cables up to several meters without reducing CPM counting results and without HV drop. Maximum probe cable length now depends mostly on the cable quality. The probe was tested and guaranteed to work with high grade low noise microphone cable of 5 meters.

    Of course, the module can be used not only for building external probes, but also for a simple radiation detectors or different microcontroller based projects where you need stable and power efficient high voltage power source to drive GM tube.

    Technical specifications:

    • Adjustable High Voltage Output 420V-550V (350V-500V version available by request)
    • Compatible with many popular GM Tubes
    • 2.5uS - 5.0uS TTL output of GM pulses
    • Ability to drive long probe cable
    • Input supply voltage 3.0V-4.5V
    • Output current 100uA max. at 550V
    • Includes 4.7M load resistor on the PCB
    • Compatible with PIC / AVR / MSP / Arduino
    • Compatible with MyGeiger ver.2 DIY Geiger Kit
    • Physical dimensions: diameter of the PCB is 53mm (LND-7317 size)
    • Shipping Weight: 150gr
    • UPC Number: 635292807381
    • SKU: RH-K-GK-HV
    Learn More
  10. High Voltage Geiger Probe Driver Power Supply Module 420V / 550V with TTL Digitized Pulse Output

    High Voltage Geiger Probe Driver Power Supply Module 400V / 500V with TTL Digitized Pulse Output

    $45.00

    Miniature Fixed Output High Voltage Power Supply Module with Digitized Output.

    Unique and miniature power supply module for Geiger tube with pulse processing circuit. The hardware will allow you to power 400V / 500V Geiger Tube and get ready digitized pulses from the output. These 5uS pulses can be counted by Arduino INT counter or any other microcontroller or ditigal counters. The module can be used for building portable DIY Geiger Counter, Dosimeter or external Geiger probe. The module is ready-to-use unit to power Geiger tube. Can be integrated into battery operated portable equipment or used for laboratory setup.

    Technical specifications:

    • Fixed High Voltage Output 420V or 500V (selected with jumper)
    • Compatible with many popular GM Tubes
    • ~ 5.0uS TTL digitized pulse output of GM pulses, VDD logic level
    • Ability to drive long probe cable
    • Input supply voltage 3.5V-5.5V
    • Output current 50uA max. at 500V
    • Quiescent battery current less than 1mA (0.1mA - 0.9mA on background)
    • Includes 10M load resistor on the PCB
    • Compatible with PIC / AVR / MSP / Arduino
    • Compatible with MyGeiger ver.2 DIY Geiger Kit
    • Physical dimensions: 40mm x 22mm 12 mm
    • Shipping Weight: 150gr
    • UPC Number: 635292807428
    • SKU: RH-K-GK-HV-2
    Learn More

10 Item(s)

per page

Set Descending Direction